Difference between revisions of "Shovel"
From A Wiki in the Desert
m (Adding English language flag using the "L" template) |
m (→top: clean up) |
||
| (12 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{Merge|Shovels}} |
| − | {{ | + | {{Item |
| − | + | | name = Shovel | |
| − | + | | image = shovel.png | |
| + | | weight = 1 | ||
| + | | bulk = 1 | ||
| + | }} | ||
| + | A '''Shovel''' is a reliable '''blacksmithed''' metal shovel made on an [[Anvil]]. It is superior to the [[Slate Shovel]] and [[Iron Shovel]]. It does not break and improves digging efficiency based on the quality. | ||
==Sources== | ==Sources== | ||
| − | Produced at a [[Anvil]] and requires [[Blacksmithing]] and [[ | + | Produced at a [[Anvil]] and requires [[Blacksmithing 1]] and [[Blacksmithing 2]] |
==Cost== | ==Cost== | ||
| Line 13: | Line 17: | ||
== Uses == | == Uses == | ||
| − | * Group [[ | + | * Group [[dig]]s to dig for [[Cuttable Stone]], [[Medium Stone]], [[gypsum]] and [[bauxite]] |
* Gather [[dirt]] from the ground. | * Gather [[dirt]] from the ground. | ||
* [[Mining Camp]] | * [[Mining Camp]] | ||
==Research and Tuition== | ==Research and Tuition== | ||
| − | *''40 Shovels (25 8500+ quality, 10 9000+ quality, 5 9500+ quality) needed for [[ | + | *''40 Shovels (25 8500+ quality, 10 9000+ quality, 5 9500+ quality) needed for [[Blacksmithing 3]] research'' |
*''100 Shovels (9500+ quality) needed for [[Storage Improvements 2]] research'' | *''100 Shovels (9500+ quality) needed for [[Storage Improvements 2]] research'' | ||
==Blacksmithing a Shovel== | ==Blacksmithing a Shovel== | ||
| − | * Put your metal on your anvil. | + | * Put your metal on your [[anvil]]. |
* Your goal is to get a lower dent in the middle, get metal to the back sides and make a flat tongue at the front. | * Your goal is to get a lower dent in the middle, get metal to the back sides and make a flat tongue at the front. | ||
| − | *Use a Shaping Mallet and try moving the metal from the area which will be the tongue in the end to the middle/back of the piece and then push it to the sides so it ends up with the height you need there. | + | *Use a [[Shaping Mallet]] and try moving the metal from the area which will be the tongue in the end to the middle/back of the piece and then push it to the sides so it ends up with the height you need there. |
*Try using force medium (7) to low (3) to get that done and shift a lot between the model and your work piece. | *Try using force medium (7) to low (3) to get that done and shift a lot between the model and your work piece. | ||
*Start at the front part where the tongue will be and try to push metal to the back. | *Start at the front part where the tongue will be and try to push metal to the back. | ||
*Hit in the front, but not the edge because you want the metal. This creates a higher ridge a bit behind the front. | *Hit in the front, but not the edge because you want the metal. This creates a higher ridge a bit behind the front. | ||
| − | *Push that back with 2 side strokes / a middle stroke if necessary and repeat. | + | *Push that back with 2 side strokes / a middle stroke if necessary and repeat. |
==See also== | ==See also== | ||
Latest revision as of 16:33, 13 May 2021
|
It has been suggested that this article or section be merged with Shovels. (Discuss)
|
| Shovel | ||
|---|---|---|
 |
||
| (Item) | ||
|
||
|
A Shovel is a reliable blacksmithed metal shovel made on an Anvil. It is superior to the Slate Shovel and Iron Shovel. It does not break and improves digging efficiency based on the quality.
Sources
Produced at a Anvil and requires Blacksmithing 1 and Blacksmithing 2
Cost
Uses
- Group digs to dig for Cuttable Stone, Medium Stone, gypsum and bauxite
- Gather dirt from the ground.
- Mining Camp
Research and Tuition
- 40 Shovels (25 8500+ quality, 10 9000+ quality, 5 9500+ quality) needed for Blacksmithing 3 research
- 100 Shovels (9500+ quality) needed for Storage Improvements 2 research
Blacksmithing a Shovel
- Put your metal on your anvil.
- Your goal is to get a lower dent in the middle, get metal to the back sides and make a flat tongue at the front.
- Use a Shaping Mallet and try moving the metal from the area which will be the tongue in the end to the middle/back of the piece and then push it to the sides so it ends up with the height you need there.
- Try using force medium (7) to low (3) to get that done and shift a lot between the model and your work piece.
- Start at the front part where the tongue will be and try to push metal to the back.
- Hit in the front, but not the edge because you want the metal. This creates a higher ridge a bit behind the front.
- Push that back with 2 side strokes / a middle stroke if necessary and repeat.
See also