Difference between revisions of "Users/Telanoc/Gears/Metals"
(Created page with "Prior to Tale 9 gearboxes only used gears of two metals, Brass and Iron. * Small Gears were made from Brass * Medium and Large Gears were made from Iron As of Tale 9, gearbox...") |
m (→top: clean up) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Users/Telanoc/Gears|Back to the Main Gear Guide]] | ||
| + | |||
Prior to Tale 9 gearboxes only used gears of two metals, Brass and Iron. | Prior to Tale 9 gearboxes only used gears of two metals, Brass and Iron. | ||
* Small Gears were made from Brass | * Small Gears were made from Brass | ||
| Line 6: | Line 8: | ||
[[File:GearMetalBox.png|none]] | [[File:GearMetalBox.png|none]] | ||
| − | This gearbox would be called "D463" for its output column and | + | This gearbox would be called "D463" for its output column and ratio. It uses the gear chain of (5/3) * (5/3) * (5/3). |
* Shaft 1A has a 5 tooth gear | * Shaft 1A has a 5 tooth gear | ||
* Shaft 2B has a 3 tooth gear on layer 1, and a 5 tooth gear on layer 2 | * Shaft 2B has a 3 tooth gear on layer 1, and a 5 tooth gear on layer 2 | ||
| Line 13: | Line 15: | ||
* Shafts 5D,6D,7D,8D have 3 tooth gears on layer 1 | * Shafts 5D,6D,7D,8D have 3 tooth gears on layer 1 | ||
| − | + | We are using the same 5/3 gear combination three times. When you go to build the box you will be asked for: | |
[[File:GearMetals.PNG|none]] | [[File:GearMetals.PNG|none]] | ||
| + | |||
| + | If we reference the Gear Ratios page we see: | ||
| + | *167 - (5/3) - Iron | ||
| + | *278 - (5/3) * (5/3) - Tin | ||
| + | *463 - (5/3) * (5/3) * (5/3) - Brass | ||
| + | |||
| + | While we are using the same combination, each increase in the ration changes the metal needed. | ||
| + | * With the first use, we are asked for 1 Medium and 1 Small Iron gear | ||
| + | * With the second use, we are asked for 1 Medium and 1 Small Tin gear | ||
| + | * With the third use, and the rest of the chain, we are asked for 1 Aluminium and 6 Brass Gears | ||
| + | |||
| + | '''''Tip''': While you can figure out all the gears you need and make them for each box you make, if you plan to make many gearboxes, it is best to make a stockpile of gears of all types ahead of time'' | ||
| + | |||
| + | {{L|en}} | ||
Latest revision as of 16:42, 13 May 2021
Prior to Tale 9 gearboxes only used gears of two metals, Brass and Iron.
- Small Gears were made from Brass
- Medium and Large Gears were made from Iron
As of Tale 9, gearboxes use gears of many different metals dependent on the gear ration. Lets look at an example gearbox:
This gearbox would be called "D463" for its output column and ratio. It uses the gear chain of (5/3) * (5/3) * (5/3).
- Shaft 1A has a 5 tooth gear
- Shaft 2B has a 3 tooth gear on layer 1, and a 5 tooth gear on layer 2
- Shaft 3C has a Spacer on layer 1, a 3 tooth on layer 2, and 5 tooth on layer 3
- Shaft 4D has a 3 tooth on layer 1, a spacer on layer 2, and 3 tooth on layer 3
- Shafts 5D,6D,7D,8D have 3 tooth gears on layer 1
We are using the same 5/3 gear combination three times. When you go to build the box you will be asked for:
If we reference the Gear Ratios page we see:
- 167 - (5/3) - Iron
- 278 - (5/3) * (5/3) - Tin
- 463 - (5/3) * (5/3) * (5/3) - Brass
While we are using the same combination, each increase in the ration changes the metal needed.
- With the first use, we are asked for 1 Medium and 1 Small Iron gear
- With the second use, we are asked for 1 Medium and 1 Small Tin gear
- With the third use, and the rest of the chain, we are asked for 1 Aluminium and 6 Brass Gears
Tip: While you can figure out all the gears you need and make them for each box you make, if you plan to make many gearboxes, it is best to make a stockpile of gears of all types ahead of time